Make Your Keurig Brew Better by Cleaning Out the Gunk

When you are utilizing your Keurig to brew espresso morning after morning, it is inevitable that gunk will accumulate over time. Mineral buildup can have an effect on how the espresso maker performs — and if sufficient of that grime reaches the inside workings, the Keurig would possibly cease operating altogether. You can stop this by giving your favourite caffeine machine a correct wipe-down once in a while. 

The brewing system, drip trays and water tanks all require frequent love and a spotlight. Even the exterior of your machine will collect unsavory stains, fingerprints and different marks of grime. Here’s the way to sort out these points earlier than issues get too far out of hand. 

Wipe the outdoors of your Keurig brewer with a humid material.

Brian Bennett/CNET

1. Clean the outdoors

Start by wiping down the brewer’s exterior. Keurig actually recommends you do that day by day. First, be sure the espresso maker is powered off and unplugged. Next use a humid material to wipe away mud and different particles from the outdoors of the machine. 

Pay shut consideration to the space on the entrance, proper under the espresso dispenser. This part sometimes attracts loads of splashes and drips.

If your Keurig brewer’s drip tray seems to be like this then it is time you clear it.

Brian Bennett/CNET

2. Wash the drip tray

Another espresso machine half that is vulnerable to grime is the drip tray. Liquid from spills typically sits inside it unnoticed. Coffee drips can evaporate right here too, leaving stains behind. A fast hand wash in the kitchen sink will clear up this mess in a jiffy. Warm water and dish cleaning soap does the trick properly. Perform this cleansing process day by day.

Clear water in a clean tray

After a fast hand wash in the sink the drip tray seems to be nice.

Brian Bennett/CNET

3. Clean the water tank

Here’s one other day by day cleansing process. That’s to present the identical hand wash remedy to the water tank. Be certain to take away the water filter first in case your machine has one. Depending in your brewer, your tank could also be protected to throw in the dishwasher.

The pod holder was the dirtiest space on my check Okay-cup brewer.

Brian Bennett/CNET

4. Check the pod holder

The dirtiest part of my check Keurig K-Classic brewer was its pod holder. Grounds, dust and dried espresso had fashioned a noticeable quantity of crud right here. To repair this, I eliminated the pod holder, and separated it into its two foremost elements. Then I gave them a water rinse and an excellent scrub with a humid material.

You may wish to use a paper clip to clear any particles from inside the brewer exit needle. The exit needle sits inside the pod holder. Take care although since that needle is sharp. Be suggested that Keurig recommends you clear the pod holder each week.

A Keurig filling a mug with brownish water

Run a water-only brew cycle to flush out your Keurig espresso machine’s brewing system.

Brian Bennett/CNET

5. Flush out the system

Keeping your Keurig machine’s brewing system clear is essential. Dirty {hardware} can result in undesirable flavors carrying over from the final brew. Tasting pumpkin spice latte in your Sumatra single origin is just not ultimate. Bits of grounds or different particles may trigger clogs too, even a malfunction.

To clear the whole lot out, run a day by day water solely brew cycle by the machine. Make certain there’s sufficient water in the reservoir and that the pod chamber is empty. You can run any cup measurement cycle you want, so long as the mug you are brewing into is giant sufficient to just accept the liquid. 

And when you’ve by no means descaled your brewer, or it has been three months since you have got, contemplate doing so. According to Keurig, it is best to carry out the process quarterly. You can use both vinegar or the firm’s special descaling product. Keep in thoughts that it’s a lengthy process requiring at the least 45 minutes (4 hours with vinegar).

Still, descaling will take away any mineral deposits (typically present in faucet water) which may be clinging to your brewer’s inside parts. This in flip ensures your espresso maker brews its optimally designed temperature. 

Once you have accomplished all these steps, wipe down the brewer once more to take away any extra moisture. It ought to now be able to brew in tip high form.


Now taking part in:
Watch this:

How to wash your Keurig with distilled vinegar


Image Credit

Leave a Comment